The Aerocompact COMPACTMETAL are specially selected and designed products, suitable for all metal roof types. The corresponding module clamps are available in the click-on version for faster assembly. The clamps are available with and without earthing pins.
With the standing seam series CompactMETAL TM, the installation of PV modules on practically all seam sheet roof types is possible. Clamps with the pre-assembled short rail are designed for direct fastening of PV modules. By optionally attaching the X40 / 50 mounting rail, the alignment of the modules is also possible in portrait mode (portrait format).
The installation of modules in portrait mode (portrait format) is easily possible using the X40 / 50 mounting rail from the CompactPITCH modular system. The rail is attached directly to the standing seam clamp with the XPN cross connector provided for this purpose. This variant can be planned in AeroTOOL.
Penetration-free fastening on the handcrafted double lock standing seam, optimum form fit due to convex/concave preformed fixing screws.
Penetration-free fastening on the craftsman angled standing seam and snap seam profiles such as Nordic Klick Falz®1, etc. Optimum form fit due to convex/concave preformed fixing screws.
Penetration-free fastening to round seam roofs like BEMO®2, Kalzip®3, Aluform®4 or RIB-ROOF Evolution®5. Optimal form fit thanks to convex/concave preformed fixing screws.
Two-piece and form-fitting clamp, especially designed for system sliding fold seam roofs such as RIB-ROOF 465®5 and GBS®6.
Two-piece and form-fitting clamp, especially designed for system sliding fold seam roofs such as Domitec®6, KLIP-LOK 406®7, SAFLOK 410®8, etc.
Two-piece and form-fitting clamp, especially designed for system sliding fold seam roofs such as KLIP-LOK 980 Optima®7, KLIP-LOK 700®7, WeatherClip 655®9, WeatherClip 700®9, etc.
Registered trademarks, by company: 1 DS Stahl GmbH; 2 BEMO SYSTEMS GmbH; 3 Kalzip GmbH; 4 Aluform System GmbH & Co. KG; 5 Zambelli Holding GmbH; 6 DOMICO Dach-, Wand- und Fassadensysteme KG; 7 BLUESCOPE STEEL LIMITED; 8 Safintra South Africa (Pty) Ltd; 9 DMI Building Products (M) Sdn Bhd.; 10 PREFA Aluminiumprodukte GmbH; 11 RHEINZINK AUSTRIA GMBH; 12 Astron Buildings GmbH
The COMPACTMETAL TR65 long rail system is fully supported on the roof structure and is therefore ideal for roof-parallel installations on sandwich panels and trapezoidal sheet metal roofs. The COMPACTMETAL TR65 long rail system does not require special approvals from panel manufacturers or additional proof of high snow loads or large purlin spacing.
The system is suitable for walkable sandwich and trapezoidal sheet metal roofs with inclinations between 0 and 70 degrees. The substructures can be made of wood or steel. The rail is mounted on the proven TS08 short rail. The rail is available in the length of 5500mm.
- System compatible click clamp
- Use of the multi-system click clamp
- No manufacturer approvals necessary
- Self supporting system
- High static stability
- High snow and wind loads
- Pitches between 0 and 70 degrees available
- Suitable for large spacing of purlins
- Suitable for core thicknesses from 60 to 160mm
- Short assembly times
- No extra drilling tools
- Suitable for steel and wooden substructures
- 25 years product warranty
- Stored in the AEROTOOL planning software
- TÜV-certified
- Developed in Austria
The CompactMETAL TS08/TS15 is our trapezoidal short rail with the best price-performance rate. The rail is pre-assembled with sealing tape and is supplied with two thin sheet screws (chip-free and thread-forming) and sealing washer.
Components to use:
Installation manual TS08-CLE10⁄CLM10
(This variant is also suitable with the TS15 short rail)
Components to use:
Installation manual TS08-EL05-CLE10⁄CLM10
(This variant is also suitable with the TS15 short rail)
The Trapezoidal sheet bridge is for longitudinal and transverse mounting.
Components to use:
Installation Manual TL38-CLE10⁄CLM10
(This variant is also suitable with the TL25)
Components to use:
Installation Manual TL38-EL05-CLE10⁄CLM10
(This variant is also suitable with the TL25)
Components to use:
Drawing TL38-EL05-PS⁄PL-CLE10⁄CLM10-LSP
Installation manual TL38-EL05-PS⁄PL
(This variant is also suitable with the TL25)
COMPACTCLAMP CLE10
Aerocompact Universal click module clamp for end positions, 30-46mm adjustable with integrated earthing pins.
COMPACTCLAMP CLM10
Aerocompact Universal click module clamp for middle positions, 30-50mm adjustable with integrated earthing pins.
CLM 10 middleclamp click 30 - 46 incl. pins
CLE10 endclamp adj 30 - 46 incl. pins
TS08 trapezoidal short rail 80 mm
TS15 trapezoidal short rail 150 mm
TL38 trapezoidal sheet bridge 380 mm
TMM08 single-seam clamp with short rail
TMR08 rounded-seam clamp with short rail
TMDS08 double-seam clamp with short rail
EL05 height adapter 33 mm
EL10 height adapter 83 mm
PS tilt adapter front 20 mm
PM tilt adapter back 100 mm
PL tilt adapter back 180 mm
LSP locking set additional elevation
EJOT JF3-2-5,5x25 E11 metal sheet screw
wire clamp 8-10 (fastening equipotential bonding)
For screwing and unscrewing stainless steel hexagon head screws without damage. The screws are secured against falling out thanks to the integrated retaining spring. Optimally suited for all cordless screwdrivers due to the ¼ " hexagonal shaft.
