COMPACTFLAT

Aerodynamic and tested base construction for elevated PV modules on flat roofs.

The aerodynamic system offers outstanding structural properties and requires significantly less ballast than other systems on the market. 

All base constructions for the CompactFLAT family are saved in our 3D engineering software AEROTool.

The AEROCOMPACT Customer Center can issue clear and competent project reports based on empirical data.

COMPACTFLAT SN10

Railbased - North/South

The COMPACTFLAT SN10 rail system as part of the COMPACTFLAT product family is an aerodynamic south/north substructure for racking and aligning framed PV modules on flat roofs.

It is available in 10° inclination. With the innovative racking system, the modules can be clamped longitudinally and short-sided.

SN10 CLAMPING ON THE LONG SIDE OF THE MODULE (DETAILS)

With longitudinal clamping COMPACTFLAT SN10 withstands the highest snow and wind loads. The extensive tests in the wind tunnel with wind speeds of up to 250 kilometers per hour and the 25-year product warranty ensure maximum safety. Since the same components are used for both the long-side and short-side construction variants, storage requirements are optimized.

SN10 CLAMP ON THE SHORT MODULE SIDE (DETAILS)

The aerodynamic construction kit system COMPACTFLAT SN10 is the most flexible rail-based assembly system on the market. It uses the same components as the east/west system COMPACTFLAT SN10PLUS, harmonizes with the most diverse module types and roof coverings and has clamps on both the short and long sides.

MAXIMUM FLEXIBILITY

No matter which frame and how many cells: The mounting solution is approved for all common module types. The universal clamps have infinitely variable height adjustment between 30 and 46 millimeters.

MAXIMUM FLEXIBILITY

MINIMUM STORAGE REQUIREMENTS

The installation has longitudinal screw channels, standard screws and low ballast. For roof coverings with less load-bearing capacity, high wind and snow loads and large modules, longitudinal clamping is the ideal solution. Since the same components are used for both variants, the storage requirement is very low.

MINIMUM STORAGE REQUIREMENTS

FLEXIBLE BALLASTIERUNG

The system offers several ballasting possibilities! Ballast stones can be easily and safely positioned by the angle rails. The ballast clamp is available with the ability to quickly and directly fix the ballast stones to the bottom rail.

FLEXIBLE BALLASTIERUNG

STABLE AND SAFE

The integrated building protection mats minimize point loads, compensate for horizontal movements (caterpillar effects) and ensure that water can drain off something good. The optionally available "Premium Pads" offer additional protection for sensitive and soft insulation surfaces. There is no need for adhesive bonding because they can be attached to the mounting system with clips.

STABLE AND SAFE

QUICK AND CONVENIENT PLANNING AND INSTALLATION

Innovative fastening methods, such as the M8 longitudinal screw channel, enable the fastest possible installations with the highest level of safety. They also save on additional screw parts. Pre-assembly can be carried out by one person without modules while standing, thus avoiding, for example, downtimes due to delivery bottlenecks. With the click clamps, the rails and modules can be mounted quickly and effortlessly.

QUICK AND CONVENIENT PLANNING AND INSTALLATION

AEROTOOL SOFTWAREINTEGRATION

Planning and simulation can be easily and conveniently implemented in just a few steps using the 3D online software AEROTOOL. The software delivers extensive information in a project report, as well as a material list with prices for automated ordering of AEROCOMPACT products.

AEROTOOL SOFTWAREINTEGRATION
  • SN10 ist FÜR HOHE WIND- UND SCHNEELASTEN GEEIGNET

    - Gültige Windgutachten nach aktuellsten Normen
    - Verbundversuchte durch offizielle Prüfinstitute
    - Belastungstests der Komponenten durch offizielle Prüfinstitute
    - Aktuellste Daten im Aerotool hinterlegt

  • FLEXIBELSTES SCHIENENSYSTEM AUF DEM MARKT

    - Baukasten mit wenig Systemkomponenten (Wenig Lager)
    - Unterschiedliche Ballastierungsmöglichkeiten verfügbar
    - Systemübergreifende Klick-Klemme ermöglicht 30-46mm Klemmhöhe

  • Längsseitige und kurzseitige Klemmung

    - Lang und Kurzseitige Klemmung mit den selben Bauteilen
    - Aufnahme von allen gängigen Modulgrößen problemlos möglich

  • Minimale Lagerhaltung

    - Systemübergreifender SN Baukasten
    - Eine Verbindungsschraube für alle Schraubverbindungen
    - Vorgefertigter Schraubkanal in den Längsschienen

  • Geringe Punktlasten durch integrierte Bautenschutzmatten

    - Unterschiedliche Bautenschutzmatten verfügbar
    - Flexible Anordnung der Protection Pads problemlos möglich

  • Für große Modulgrößen geeignet

    - Die längsseitge Klemmung ermöglicht die Aufnahme von großen PV-Modulen

COMPACTFLAT SN10PLUS

Railbased - East/West

The­COMPACTFLAT SN10+ rail system,­as­ part­ of ­the­ COMPACTFLAT­ group, ­is­ an­ aerodynamic­ east/west-facing ­racking ­for­ the ­in- stallation­ of­ PV modules­ on ­flat­roofs.­The­ system ­is­ available at ­a ­tilt­ of­ 10°.­

The ­innovative­ racking ­system­ allows ­longside and shortside clamping. ­The ­mid backing is a combination of two mirrored support from ­the SN10 system.­

SN10 KLEMMUNG AN DER LANGEN MODULSEITE (DETAILS)

Mit längsseitiger Klemmung hält COMPACTFLAT SN10 den höchsten Schnee- und Windlasten stand. Die umfangreichen Tests im Windkanal mit Windgeschwindig-keiten von bis zu 250 Kilometern pro Stunde und die 25−jährige Produktgarantie gewährleisten maximale Sicherheit. Da für die längsseitigen als auch bei der kurzseitigen Konstruktionsvariante dieselben Komponenten verwendet, ist der Lagerbedarf optimiert. 

SN10 KLEMMUNG AN DER KURZEN MODULSEITE (DETAILS)

Das aerodynamische Baukastensystem COMPACTFLAT SN10 ist das flexibelste schienenbasierte Montagesystem auf dem Markt. Es verwendet die gleichen Komponenten wie das Ost/West-System COMPACTFLAT SN10PLUS, harmoniert mit den unterschiedlichsten Modultypen und Dacheindeckungen und lässt sich sowohl auf der kurzen als auch auf der langen Seite klemmen.

MAXIMUM FLEXIBILITY

No matter which frame and how many cells: The mounting solution is approved for all common module types. The universal clamps have infinitely variable height adjustment between 30 and 46 millimeters.

MAXIMUM FLEXIBILITY

MINIMUM STORAGE REQUIREMENTS

The installation has longitudinal screw channels, standard screws and low ballast. For roof coverings with less load-bearing capacity, high wind and snow loads and large modules, longitudinal clamping is the ideal solution. Since the same components are used for both variants, the storage requirement is very low.

MINIMUM STORAGE REQUIREMENTS

FLEXIBLE BALLASTIERUNG

The system offers several ballasting possibilities! Ballast stones can be easily and safely positioned by the angle rails. The ballast clamp is available with the ability to quickly and directly fix the ballast stones to the bottom rail.

FLEXIBLE BALLASTIERUNG

STABLE AND SAFE

The integrated building protection mats minimize point loads, compensate for horizontal movements (caterpillar effects) and ensure that water can drain off something good. The optionally available "Premium Pads" offer additional protection for sensitive and soft insulation surfaces. There is no need for adhesive bonding because they can be attached to the mounting system with clips.

STABLE AND SAFE

QUICK AND CONVENIENT PLANNING AND INSTALLATION

Innovative fastening methods, such as the M8 longitudinal screw channel, enable the fastest possible installations with the highest level of safety. They also save on additional screw parts. Pre-assembly can be carried out by one person without modules while standing, thus avoiding, for example, downtimes due to delivery bottlenecks. With the click clamps, the rails and modules can be mounted quickly and effortlessly.

QUICK AND CONVENIENT PLANNING AND INSTALLATION

AEROTOOL SOFTWAREINTEGRATION

Planning and simulation can be easily and conveniently implemented in just a few steps using the 3D online software AEROTOOL. The software delivers extensive information in a project report, as well as a material list with prices for automated ordering of AEROCOMPACT products.

AEROTOOL SOFTWAREINTEGRATION
  • SN10 ist FÜR HOHE WIND- UND SCHNEELASTEN GEEIGNET

    - Gültige Windgutachten nach aktuellsten Normen
    - Verbundversuchte durch offizielle Prüfinstitute
    - Belastungstests der Komponenten durch offizielle Prüfinstitute
    - Aktuellste Daten im Aerotool hinterlegt

  • FLEXIBELSTES SCHIENENSYSTEM AUF DEM MARKT

    - Baukasten mit wenig Systemkomponenten (Wenig Lager)
    - Unterschiedliche Ballastierungsmöglichkeiten verfügbar
    - Systemübergreifende Klick-Klemme ermöglicht 30-46mm Klemmhöhe

  • Längsseitige und kurzseitige Klemmung

    - Lang und Kurzseitige Klemmung mit den selben Bauteilen
    - Aufnahme von allen gängigen Modulgrößen problemlos möglich

  • Minimale Lagerhaltung

    - Systemübergreifender SN Baukasten
    - Eine Verbindungsschraube für alle Schraubverbindungen
    - Vorgefertigter Schraubkanal in den Längsschienen

  • Geringe Punktlasten durch integrierte Bautenschutzmatten

    - Unterschiedliche Bautenschutzmatten verfügbar
    - Flexible Anordnung der Protection Pads problemlos möglich

  • Für große Modulgrößen geeignet

    - Die längsseitge Klemmung ermöglicht die Aufnahme von großen PV-Modulen

CompactFLAT S05/10/15

Bracket Based - North/South

The system is part of the CompactFLAT product family and an aerodynamic South base construction for attaching and aligning PV modules on flat roofs.

It is available in 5°, 10° and 15° tilts, and in different row spacings. 

The CompactFLAT S has a 25-year warranty, has been tested in the wind tunnel, is certified in accordance with UL 2703 TÜV, and is delivered with pre-mounted protective mats.

All variants are tested and approved by TÜV Rheinland according to UL 2703 using load testing, and according to UL 1703 using fire testing.

The cable management for string wiring of module series is UL certified and available as an accessory to the base structure.

COMPACTFLAT S10PLUS

BRACKETBASED - East/West

Compact, tested base construction for double-sided elevated PV modules on flat roofs.

The system is part of the CompactFLAT product family and an aerodynamic EAST/WEST base construction for attaching and aligning PV modules on flat roofs. The system is available in 10° tilt and with different row spacing.

With just three main components, CompactFLAT S10+ offers an outstanding price-performance ratio. The simple installation and good transport density of the innovative system saves time and resources while offering an inexpensive system price.

The aerodynamic design offers outstanding structural properties and requires significantly less ballast than other systems on the market. 

Thanks to the unique “spring effect” of the stand, the base structure adapts optimally to surface conditions. Because the construction is not attached to fails, water drainage is ensured on all sides.

CompactFLAT S10+ is delivered pre-assembled, including newly developed protective mat with long-term durability testing.

Download new product brochure

Downloads

Downloads CompactFLAT SN

  • CompactFLAT SN10 - Leaflet ende
  • CompactFLAT SN10 - Checklist ende
  • CompactFLAT SN10 - Assembly instructions long-side clamping ende
  • CompactFLAT SN10 - Assembly instructions short-side clamping ende
  • CompactFLAT SN10PLUS - Assembly instructions short-side clamping ende
  • CompactFLAT SN10PLUS - Assembly instructions long-side clamping ende
  • Instruction for the measurement of the static friction coefficient ende

Downloads CompactFLAT S

  • CompactFLAT S05 - Leaflet ende
  • CompactFLAT S10 - Leaflet ende
  • CompactFLAT S15 - Leaflet ende
  • CompactFLAT S05/10/15 - Checklist ende
  • CompactFLAT S05/10/15 - Assembly instruction ende
  • CompactFLAT S10PLUS - Leaflet ende
  • CompactFLAT S10PLUS - Assembly instruction ende
  • Instruction for the measurement of the static friction coefficient ende

General

AssemblyVideos

  • CompactFLAT S05

  • CompactFLAT S15

  • CompactFLAT S plus

  • Cable management | Kabelmanagement

  • Alpin Version

  • Ballast tray - front bracket | Ballastierungswanne - Anfangsfuss

  • Ballast tray - connector | Ballastierungswanne - Verbinder

  • Ballast tray - end bracket | Ballastierungswanne - Endfuss

  • Direct ballasting | Direkte Ballastierung

We areAEROCOMPACT

Curious what we can do for you?

Can we help you with additional information, an offer, or a tender text? Please let us know!

Inquiry form

I am interested in
your company
Your company
You are
Your information
Send
Send

European headquarters

USA headquarters

Headquarter India

  • AEROCOMPACT® India Private Ltd. 
    Hub and Oak
    C-360, Defence Colony
    New Delhi, 110024
  • +91 888 26 32 902
  • office.in@aerocompact.com