COMPACTPITCH XM-F

THE UNIVERSAL ROOF HOOK SYSTEM AS A WORLD PREMIERE

Years product warranty
CE marked

LOADABLE.
COST EFFICIENT.
Effortless.

The COMPACTPITCH XM-F REPTILE system offers an innovative solution for a wide range of different roof tiles on pitched roofs, with a flexible cover that can be adapted to the tile shape. The roof hook can therefore always be mounted centrally on the rafter, regardless of the tile pitch, guaranteeing optimal force application.

The XM-F system is a new type of roof hook design that is particularly strong due to the optimized force transmission into the rafters. This makes installation in areas with high snow loads much easier to realize. In zones with lower snow loads, the number of roof hooks can be significantly reduced by combining them with the X60 rail, thus saving installation time and costs.

AEROCOMPACT's Pierce Labyrinth Seal allows flexible positioning of the XM-F roof hook on the XM-FC cover plate. The roof hook can therefore always be mounted centrally on the rafter, regardless of the tile position, guaranteeing optimal force transmission. This results in an enormous load-bearing capacity of the roof hook and, depending on the area of application and system combination, leads to a significant reduction of fastening points.

Cost-effective due to savings on roof hooks
Pre-assembled assembly
Mounting always on rafters, thus highest load capacities possible
Up to 40 percent time saving
Highest load capacity
Adaptable to almost any tile shape
Flexible in application

Standard composite

By default, the PV modules are attached directly to the base rails in portrait mode (portrait format).

Cross-connection

The installation of modules in Landscape Mode (landscape format) can be implemented using additional mounting rails. These are fastened directly to the standard base rails using the XPN cross connector.

Roof hooks

The aluminum roof hook is pre-assembled with stainless steel screws and can be adjusted according to the roof batten height. The quick-release clamp simplifies the mounting of the X60 rail.

Support plate

The support plate is made of galvanized steel sheet and supports the cover plate when the roof hooks are exposed.
(The support plate does not serve as step protection.)

Mounting rail X60

The aluminum profile rail is the central construction element, which offers a high static load capacity due to its optimized shape.

CLE10/CLM10 module clamps

The PV modules are held in place using the universal click clamp with integrated grounding pins. The multi-system clamp is height-adjustable between 30 - 46 mm and can be conveniently clicked into place. The end clamp has a length of 60 mm. The clamps are also available in black.

Video

Cover plate

The cover plate allows positioning the roof hook always directly above the rafter, is made of aluminum and can be easily adjusted to the contour of the roof tiles. It is available in three colors.

Cross connector

The cross connector bracket can be used to connect mounting rails together, allowing for additional alignments and positions of the PV modules. The cross connector is also available in black.

OPTIMIZE YOUR INSTALLATION WITH THE RIGHT ACCESSORIES.

01. Foam wedge
02. Ground plate/Rail bridge
03.Spacer plate

foam wedge

For additional sealing in the case of high brick shafts, we recommend using a foam wedge in this area. This one meter long strip is cut to the required length and attached to the cover plate under the tile above, using self-adhesive tape.

ground plate/rail bridge

With the rail bridge we enable the installation of the REPTILE also between two rafters. Thus, the otherwise exposed roof hook can be placed under the module. Placement takes place with a rafter spacing of max. 900 mm. Delivery length 1980 mm, cutting and perforation is to be done on site.

The grub screw (701590) is required for mounting the XM-F REPTILE.

spacer plate 2.5/5.0 mm

In certain situations, it may be necessary to raise the XM-F REPTILE. For this purpose, there is now a spacer plate for substructure. This fits exactly under the base plate and can be easily used for 2.5 or folded for 5mm increase.

End cap for mounting rail X60

For the clean covering of the open mounting rails as well as for the aesthetic enhancement of the PV system, we offer the optional end caps made of UV-stabilized polyamide.

SELECT YOUR SYSTEM

PV-module alignment

XM-F

CompactPITCH XM-F

PV-module alignment: Portrait

XM-F

CompactPITCH XM-F cross-connection

PV-module alignment: Landscape

DOWNLOADS

Leaflet COMPACTPITCH XM-F
DE EN IT NL ES
Checklist COMPACTPITCH XM-F
DE EN
Assembly instructions COMPACTPITCH XM-F
DE EN
Compatibility roof tile COMPACTPITCH XM-F
DE EN

ProjeCTS

Flat roofs

COMPACTFLAT // Substructure for PV systems on flat roofs

GROUND MOUNT

COMPACTGROUND// Substructure for PV systems on open spaces

Metal roofs

COMPACTMETAL// Substructure for PV systems on metal roofs

THE UNIVERSAL ROOF HOOK SYSTEM AS A WORLD PREMIERE